 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| SILICON MMIC UPC2721GV L BAND DOWNCONVERTER FEATURES * WIDE BAND OPERATION UP TO 2.5 GHz * INTERNAL BALANCED AMPLIFIER FOR VCO * SINGLE ENDED PUSH-PULL IF AMPLIFIER * 5 V SINGLE SUPPLY VOLTAGE: ICC = 30 to 35 mA * LOW CURRENT DISSIPATION * TAPE AND REEL PACKAGING OPTION AVAILABLE OSC base (feedback) 2 OSC BUFFER INTERNAL BLOCK DIAGRAM OSC base (bypass) 1 OSC 8 RFIN1 7 RFIN2 (bypass) DESCRIPTION The UPC2721GV is a L-Band frequency converter manufactured using the NESAT III MMIC process. This product consists of a double balanced mixer, local oscillator, IF preamplifier, and constant voltage generator. It is available in a 8 pin SSOP package. This device is designed for low cost cellular radios, GPS receivers, PCS, and UHF TV tuner applications. The UPC2721 output amplifier is a single-end push-pull amplifier designed for operation into a 50 load. NEC's stringent quality assurance and test procedures ensure the highest reliability and performance. OSC collector (coupling) 3 6 GND IF AMP VCC 4 REG. MIX 5 IFOUT ELECTRICAL CHARACTERISTICS (TA = 25C, VCC = 5 V, PLO = -10 dBm) PART NUMBER PACKAGE OUTLINE SYMBOLS ICC fRF fIF CG PARAMETERS AND CONDITIONS Circuit Current RF Frequency Range IF Frequency Range Conversion Gain2 fRF = 900 to 2000MHz,fIF = 50 to 400 MHz fIF = 400 to 400 MHz Saturated Output Power2 fRF = 800 to 2000 MHz, fIF = 400 MHz Noise FigurefRF = 900 MHz, fIF = 400 MHz, fRF = 2.0 GHz, fIF = 400 MHz SSB Third Order Intercept Point, f1 = 900 MHz, f2 = 938 MHz f1 = 2.0 GHz, f2 = 2.038 GHz UNITS mA GHz MHz dB dB dB dBm dBm dB dB dBm dBm UPC2721GV S08 MIN 29 0.9 50 18 21 22 19.5 7 7 9 11 +10 +8.5 13 15 TYP 38 MAX 45.5 2.0 600 24 PSAT NF IP3 2 Notes: 1. Mounted on a 50 x 50 x 1.6 mm thick glass epoxy board with double sided copper. 2. Minimum and maximum specifications for CG and PSAT are measured at fRF = 900 MHz and 2.0 GHz and at fIF = 402.8 MHz. California Eastern Laboratories UPC2721GV ABSOLUTE MAXIMUM RATINGS1 (TA = 25C) SYMBOLS VCC2 PT3 TOP TSTG PARAMETERS Supply Voltage Power Dissipation3 Operating Temperature Storage Temperature UNITS V mW C C RATINGS 6 250 -40 to +85 -65 to +150 Notes: 1. Operation in excess of any one of these parameters may result in permanent damage. 2. Recommended operating VCC range is 4.5 to 5.5 V MAX. 3. TA = +85C mounted on a 50 x 50 x 1.6 mm thick glass epoxy board with double sided copper. TYPICAL PERFORMANCE CURVES (TA = 25C) CIRCUIT CURRENT VS. SUPPLY VOLTAGE 60 No Input Signal +10 fRF = 2 GHz fRF = 900 MHz OUTPUT POWER VS. INPUT POWER 40 Output Power, POUT (dBm) Circuit Current, ICC (mA) 50 +5 0 30 -5 20 -10 10 -15 VCC = 5 V fIF = 402 MHz 0 1 2 3 4 5 6 -20 -40 -30 -20 -10 0 +10 +20 Supply Voltage, VCC (V) Input Power, PIN (dBm) CONVERSION GAIN AND NOISE FIGURE vs. RF FREQUENCY 30 30 VCC = 5 V PRF = -30 dBm PLO = -5 dBm fIF = 402 MHZ CG 20 UPC2721 CONVERSION GAIN vs. IF FREQUENCY Noise Figure, NF (dB) Conversion Gain, CG (dB) Conversion Gain, CG (dB) 25 25 fRF = 2.0 GHz 20 fRF = 900 MHZ 15 15 10 NF 5 10 5 0 0.5 1.0 1.5 2.0 2.5 3.0 0 VCC = 5 V PLO = 0 dBm PRF = -30 dBm 100 200 300 400 500 600 Input Frequency, fRF (GHz) IF Frequency, fIF (MHz) UPC2721GV TYPICAL PERFORMANCE CURVES (TA = 25C) IM3 AND OUTPUT POWER vs. INPUT POWER OSC FREQUENCY STABILITY vs. OSC FREQUENCY Output Power, POUT (dBm) 3rd Order Intermodulation Distortion, IM3 (dBm) Oscillation Frequency Stability, fSTB (MHz) +10 +6.0 0 -10 -20 -30 -40 -50 Pout VCC = 4.5 V +4.0 VCC = 5.5 V +2.0 IM3 0 VCC = 5.5 V -2.0 -60 fRF1 = 900 MHZ fRF2 = 938 MHZ fLO = 1.3 GHZ (0 dBm) fRF1 = 2.0 GHZ fRF2 = 2.038 GHZ fLO = 2.4 GHZ (0 dBm) -40 -30 -20 -10 0 VCC = 4.5 V -4.0 -6.0 -1.4 -1.5 -1.6 -1.7 -1.8 -1.9 -2.0 -2.1 -2.2 Input Power, PIN (dBm) Oscillation Frequency, fOSC (GHz) PIN DESCRIPTIONS PIN NO. 1 SYMBOL OSC base (bypass) PIN VOLT TYP (V) 2.9 DESCRIPTION Internal oscillator consists of a balance amplifier. Pin 2 and pin 3 should be externally equipped with a tank resonator circuit in order to oscillate with feedback loop. Pin 1 should be grounded through coupling capacitor ~0.5 pF. EQUIVALENT CIRCUIT 2 Vcc 3 1 2 OSC base (feedback) 2.9 3 OSC collector (coupling) VCC IF Output 5.0 Pin 3 is an open collector. This pin should be coupled through resistor or choke coil in order to adjust Q and connect the supply voltage. Supply voltage pin for the IC. The amplifier is designed as single-ended push-pull amplifier. This pin is an emitter follower output with a wideband 50 impedance. 4 5 5.0 2.9 40 5 6 7 GND RF input2 (bypass) 0.0 2.4 GND pin for the IC. Pin 7 and pin 8 are inputs to a doublebalanced mixer. Either pin can be assigned for input or ground. 8 RF input1 2.4 7 8 UPC2721GV TEST CIRCUITS 100 pF 1 0.5 pF 8 RF IN LO IN 100 pF 10 2 7 2 pF 20 pF 3 100 4 100 pF 20 pF 6 1000 pF 5 1.8 H IF OUT 5.0 V APPLICATION CIRCUIT VTUNE 1000 pF 51k 100 pF ALPHA SMV1204-04 1 3.3nH 1pF 2 1pF 1pF 3 47 4 5 1.8 H 18nH 6 1000 pF IF OUT 7 2 pF 20 pF 8 RF IN 10pF 20pF 5.0 V UPC2721GV OUTLINE DIMENSIONS (Units in mm) UPC2721GV PACKAGE OUTLINE S08 8 7 6 5 N 2721 XXX 2 3 3.0 MAX 4 +0.10 0.15 -0.05 Detail of Lead End 1 3 -3 +7 4.94 0.2 3.20.1 0.870.2 1.50.1 1.8 MAX 0.1 0.1 0.65 +0.10 0.3 -0.05 0.5 0.2 0.575 MAX LEAD CONNECTIONS 1. 2. 3. 4. 5. 6. 7. 8. OSC-Base (Bypass) OSC-Base (Feed back) OSC-Collector (Coupling) VCC IF OUT GND RFIN2 RFIN1 Notes: Package will be marked as 2721 as shown. All dimensions are typical unless otherwise specified. Lead Material: Alloy 42 Lead Plating: Lead tin alloy ORDERING INFORMATION PART NUMBER UPC2721GV-E1 QTY 1000/Reel Life Support Applications These NEC products are not intended for use in life support devices, appliances, or systems where the malfunction of these products can reasonably be expected to result in personal injury. The customers of CEL using or selling these products for use in such applications do so at their own risk and agree to fully indemnify CEL for all damages resulting from such improper use or sale. EXCLUSIVE NORTH AMERICAN AGENT FOR NEC RF, MICROWAVE & OPTOELECTRONIC SEMICONDUCTORS CALIFORNIA EASTERN LABORATORIES * Headquarters * 4590 Patrick Henry Drive * Santa Clara, CA 95054-1817 * (408) 988-3500 * Telex 34-6393 * FAX (408) 988-0279 Internet: http://WWW.CEL.COM DATA SUBJECT TO CHANGE WITHOUT NOTICE 01/16/2001 |
Price & Availability of UPC2721GV
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |